Eurorack Kits

Showing 1-65 of 65 item(s)

Full Kits

1U TRS DIY Kit

€30.00

DIY version of our TRS. Total flexibility for the Befaco 7U or Intellijel cases rear connectors Jacks. The channels are reversible and can be used independently for Input or Output. 4 Inputs or Outputs (per module) can be obtained by “Y” cables. Independent tip and ring attenuators are selectable for each channel to convert the Modular Input Level to Line...

Friends

1U Motion MTR DIY Kit

1UDIYMT001

€105.00

Motion MTR allows you to mix, attenuate and invert signals while having clear visual feedback of their levels. Each channel can function as: Audio level control with VU meter CV attenuator with voltage meter CV inverter with voltage meter Each input is connected to 10V, so you can use each of them to generate fixed voltages. Also, the outputs of...

Full Kits

1U STAmp DIY Kit

1UDIY042

€55.00

ST Amp is a 1U stereo amplifier designed to boost your external signals into modular levels. The module is designed under the Intellijel 1U format and uses the same pinout, making it fully compatible with the Intelljel case’s rear connectors.

Full Kits

1U STMix DIY KIt

1UDIY022

€60.00

STMix is a four-channel stereo mixer in 28hp and 1U format. It can work independently or as an expansion of our Hexmix module via the six-pin connector located in the back. The module is designed under the Intellijel 1U format.

Full Kits

1U Out DIY Kit

1UDIY021

€55.00

Out is a 1U stereo output module designed to convert audio signals from your modular to line-levels. The module is designed to be used on cases with onboard Jack connectors or Intellijel 7U and Palette series, as it uses the same pinout. The module also includes a high-quality Headphone amplifier with an auxiliar monitoring CUE input.

Out of stock

Divkid

Divkid Stereo Strip - DIY kit

DKY002

€90.00

DIY version of the Divkid Stereo Strip module. Stereo Strip is a 6HP Eurorack module that builds upon the idea of a studio or mixer channel strip for a modular environment. If you’re new to the term ‘channel strip’ think of a single channel strip from a mixing desk. You’ll find amplification, EQ, panning, and level control options. Stereo Strip builds on...

View

Friends

Motion MTR - DIY Kit

MTK001

€95.00

DIY version of our Motion MTR module Motion MTR allows you to mix, attenuate and invert signals while having clear visual feedback of their levels. Each channel can function as: Audio level control with VU meter CV attenuator with voltage meter CV inverter with voltage meter Each input is connected to 10V, so you can use each of them to generate...

Divkid

Divkid Mutes - DIY Kit

DKY001

€80.00

DIY kit of the Divkid Mutes module. Mutes goes above and beyond basic muting by allowing you to split groups of signals to multiple destinations, making it great for FX dub performing and varied signal routing. Vactrols on the circuit gives to the switching a pleasing decay for both audio and modulation as well a totally click free muting. Three-position...

Full Kits

Pony VCO DIY Kit

DIY040

€150.00

DIY Version of our Pony VCO module. This is a pre-soldered DIY Kit. Pony VCO is a fully analog Thru-Zero oscillator with wavefolder and dedicated VCA in only 4HP. The module offers great stability and tuning capabilities thanks to its powerful core, based onSound Semiconductors IC. It comes with range selector, that allows it to go down to LFO range, as...

Out of stock

Full Kits

ACDC DIY Kit

DIY039

€170.00

DIY version of our ACDC Eurorack module AC/DC is a class-compliant DC coupled audio interface in Eurorack format. With its 6 HP, it is perfect for live performance and travel Rigs.Based on Rebel Technology OWL platform, It allows sending and receiving both CV and Audio at 16 bits 48 kHz. as well as load patches from Rebel’s library.It is compatible with...

View

Full Kits

Noise Plethora DIY Kit

DIY037

€205.00

DIY version of Noise Plethora Module. Noise Plethora is a multitimbral noise monster in 14HP.The module consists of three digital sound generators, followed by three analog multimode Filters. This combination makes it easy to sculpt different textures and noises and play with them intuitively and musically.The first two channels let you choose from...

Full Kits

MEX DIY Kit

DIY038

€50.00

DIY version of our Mex module. MEX, is a gate expander for Muxlicer! It adds a new line of gates to Muxlicer’s sequence, where you can choose to turn off the step, output the same number of gates as muxlicer, or send just one. A very simple concept, that provides great flexibility! And the greatest thing: you can daisy chain them so you can add as many as...

Full Kits

Hexmix DIY Kit

DIY017

€225.00

DIY kit version of our Hexmix Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and four of our bespoke Knurlies M3 rack screws. Hexmix System is a six channel performance mixer specially designed for Eurorack. The system has two separate modules, the core of the mixer: Hexmix that has six...

Out of stock

Full Kits

Spring Reverb DIY Kit

DIY011

€130.00

DIY kit version of our Spring Reverb Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and four of our bespoke Knurlies M3 rack screws. REVERB TANK INCLUDED This is our take on an analog spring reverb module. Featuring VCAs for the two available inputs (with different routing), CV control for...

View

Full Kits

Mixer DIY Kit

DIY009

€50.00

DIY kit version of our Mixer Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and four of our bespoke Knurlies M3 rack screws. A four-channel mixer, suitable for audio or control signals. It features regular and inverted outputs as well as an LED level meter. Current needs: +12V: 21mA, -12V:...

Full Kits

Percall DIY Kit

DIY033

€150.00

DIY kit version of our Percall Eurorack module. The kit includes all the necessary parts to make a completed module including power cable, four of our bespoke Knurlies M3 rack screws and Bananuts! Percall is a percussive oriented module that will shape four different sound sources into percussive sounds. Percall has four VCAs with dedicated decay...

Full Kits

Burst DIY Kit

DIY020

€100.00

DIY kit version of our Burst Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and four of our bespoke Knurlies M3 rack screws. Burst is a Pingable Trigger Burst generator with distribution, probability, and time division control. It will create multiplications of your triggers, leading to...

Full Kits

Hexpander DIY Kit

DIY018

€235.00

DIY kit version of our Hexpander Eurorack module. The kit includes all the necessary parts to make a completed module including power cable, Hexmix VCA connector cable and four of our bespoke Knurlies M3 rack screws. Hexpander adds great functionality to Hexmix module. Featuring Three aux send with stereo returns, individual outputs for each channel,...

Out of stock

Full Kits

InAmp DIY Kit

DIY024

€65.00

DIY kit version of our InAmp Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and our bespoke Knurlies M3 rack screws. Inamp is a dual pre-amp in just 4 HPs. Featuring 6,3 Jacks inputs as well as Minijacks. Both inputs are summed so you can use them at the same time as an input mixer. The unit is...

View

Full Kits

VC Slew Limiter DIY Kit

DIY012

€55.00

DIY kit version of our VC Slew Limiter Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and four of our bespoke Knurlies M3 rack screws. A voltage-controlled slew limiter, AKA Lag Processor. A slew limiter is a device that smoothes an incoming signal, limiting the maximum rate of the output...

Out of stock

PCB & Panels

Pony VCO 1U Mod Kit

DIY1U040

€10.00

Front Panel Kit with the instructions to turn your Pony VCO 3U into a 1U module. Pony VCO is a fully analog Thru-Zero oscillator with wave-folder and dedicated VCA in only 4HP. The module offers great stability and tuning capabilities thanks to its powerful core, based onSound Semiconductors IC. It comes with a range selector, that allows it to go down...

View

Full Kits

Sampling Modulator DIY Kit

DIY010

€110.00

DIY kit version of our Sampling Modulator Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and two of our bespoke Knurlies M3 rack screws. The Sampling Modulator is a multi-function module that lies somewhere between a VCO, a Sample & Hold, and an 8 step trigger sequencer. FEATURES Sequencer...

Full Kits

BF-22 VCF DIY Kit

DIY005

€125.00

DIY kit version of our BF-22 VCF Eurorack module. The kit includes all the necessary parts to make a completed module including a power cable and four of our bespoke Knurlies M3 rack screws. The BF-22 VCF is a dual Hi/Low-pass filter inspired by the Sallen-Key filter from the early MS-20. FEATURES The module features attenuverters...

Partial Kits

Percall Partial Kit

PTDIY033

€86.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Percall module. Includes PCB/Panel Set + Rare parts. Percall is a percussive-oriented module that will shape four different sound sources into percussive sounds. Percall has four VCAs with dedicated decay envelopes and a mixer, so you can prepare a percussion submix. Added strength input will provide...

Full Kits

Lich DIY Kit

DIY035

€170.00

DIY version of our Lich Module. Knurlies included. Lich is a programmable multi-function module based on Rebel Technology OWL platform. This is a Befaco Rebel collaboration that brings back Owl’s platform with this new hardware iteration. It has stereo in and out, four pot controls summed to cv inputs (like the classic Owl module) And as addition, CV and...

Partial Kits

VCMC Partial Kit

PTDIY031

€95.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our VCMC module. Includes PCB/Panel Set + Rare parts. VCMC is a voltage-controlled MIDI controller. A fully editable MIDI controller with eight faders and push buttons. Each of them with a CV or Gate input associated to automate their functioning via external signals or to be configured independently for...

Full Kits

CV Thing DIY Kit

DIY034

€150.00

DIY version of our CV Thing Module. CV Thing is a fully mappable CV to MIDI converter in just 6HP. Its based on our VCMC module, but aiming for small and compact performance rigs. It has eight inputs that can be mapped to any MIDI message quite easily thanks to its simple and intuitive user interface. CCs, Program change ,V/Oct to Note or Clock are some...

Full Kits

Dual Attenuverter DIY Kit

DIY007

€50.00

DIY kit version of our Dual Attenuverter Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and two of our bespoke Knurlies M3 rack screws. The Dual Atenuverter is a CV/Audio utility module designed to atenuate, invert and apply offset to an input signal. The “ATENUVERTER” pot will multiply your...

Partial Kits

STMix Partial Kit

PTDIY022

€45.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our STMix module. Includes PCB/Panel Set + Rare parts. STMix is a compact 4 channel stereo mixer with an auxiliary input. This input will allow us to chain a few of them or to insert an extra fifth input. This module is compatible with our Hexmix System and can be internally connected to the Hexmix module...

Full Kits

Instrument Interface DIY Kit

DIY032

€130.00

DIY Version of our Instrument Interface Module. Instrument Interface is an eurorack pre-amp capable to bring any type of audio signal to modular levels thanks to its amplification circuit. The module can drive regular and condenser microphones (+48V Phantom Powered) as well as Instrument and Line signals with a very low distortion ratio. Instrument...

Full Kits

Chopping Kinky DIY Kit

DIY015

€110.00

DIY kit version of our Chopping Kinky Eurorack module. The kit includes all the necessary parts to make a completed module including a power cable and two of our bespoke Knurlies M3 rack screws. Chopping kinky is a voltage controllable, dual-channel wavefolder. As a unique feature, it has a chop out that will choose between both channels with a zero...

Partial Kits

Spring Reverb Partial Kit

PTDIY011

€48.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Spring Reverb module. Includes PCB/Panel Set + Rare parts. This is our take on an analog spring reverb module. Featuring VCAs for the two available inputs (with different routing), CV control for DRY/WET and visual feedback for signal levels at input and output of the tank. Two CV-controlled audio...

Full Kits

Output V3 DIY Kit

DIY021

€65.00

DIY kit version of our new Output V3 Eurorack module. The kit includes all the necessary parts to make a completed module including a power cable and four of our bespoke Knurlies M3 rack screws. Our new Output Module is designed to be the master output for your modular system, providing an extra Cue Input to monitor any signal. FEATURES Left IN is...

Full Kits

Even VCO DIY Kit

DIY014

€110.00

DIY kit version of our EvenVCO Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and four of our bespok Knurlies M3 rack screws. The Even VCO is a voltage controlled oscillator which offers stability even in the case of power supply fluctuations. 10 position octave selector 1 cent precision...

Partial Kits

VC Slew Limiter Partial Kit

PTDIY012

€34.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our VC Slew Limiter module. Includes PCB/Panel Set + Rare parts. A voltage-controlled slew limiter, AKA Lag Processor. A slew limiter is a device that smoothes an incoming signal, limiting the maximum rate of the output voltage over time. It is widely used with pitch CVs to obtain portamento and CV...

Full Kits

VCMC DIY Kit

DIY031

€180.00

DIY version of our VCMC Module. VCMC is a voltage-controlled MIDI controller. A fully editable MIDI controller with eight faders and push-buttons. Each of them with a CV or Gate input associated to automate their functioning via external signals or to be configured independently for further control. Each control on VCMC can be edited on its OLED screen...

Full Kits

VC ADSR DIY Kit

DIY013

€95.00

DIY kit version of our VC ADSR Eurorack module. The kit includes all the necessary parts to make a completed module including a power cable and four of our bespoke Knurlies M3 rack screws. Assembled Version of our VC ADSR module. Knurlies included, The VC ADSR is our take on the classic ADSR: now smaller, more powerful, and user friendly. FEATURES...

Partial Kits

Output Partial Kit

PTDIY021

€38.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Output module. Includes PCB/Panel Set + Rare parts. Our new Output Module is designed to be the master output for your modular system, providing an extra Cue Input to monitor any signal. FEATURES Left IN is routed to both channels when no Right signal is present. Both Outputs are TRS balanced. A...

Full Kits

Kickall DIY Kit

DIY023

€115.00

DIY kit version of our Kickall Eurorack module. The kit includes all the necessary parts to make a completed module including PCB, components, aluminium front panel, power cable and a set of our bespoke Knurlies M3 rack screws. Kickall is a 6HP compact synth voice that features everything needed to make a big fat Kick sound: A stable VCO that tracks...

Partial Kits

Muxlicer Partial Kit

PTDIY019

€75.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Muxlicer module. Includes PCB/Panel Set + Rare parts. Muxlicer is a sequential signal processor designed to add a huge range of special functions to your modular setup in the minimum space. Is divided into three main blocks: a Digital Step Controller, a Gate Generator, and an Analog Switch (a.k.a....

Full Kits

Rampage DIY Kit

DIY004

€155.00

DIY kit version of our Rampage Eurorack module. The kit includes all the necessary parts to make a completed module including a power cable and four of our bespoke Knurlies M3 rack screws. Rampage is Befaco’s approach to an old invention: the Serge/Buchla ramp generator. We took the idea of a “patch programmable” function generator/processor, put two...

Partial Kits

Mixer Partial Kit

PTDIY009

€36.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Mixer module. Includes PCB/Panel Set + Rare parts. A four-channel mixer, suitable for audio or control signals. It features regular and inverted outputs as well as an LED level meter. Current needs: +12V: 21mA, -12V: 10mA Width: 5 HP Depth: 20mm (including power connector) Aluminum, heat-treated...

Full Kits

A*B+C DIY Kit

DIY001

€90.00

DIY kit version of our A*B+C Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and our bespoke Knurlies M3 rack screws. A*B+C is a dual, four-quadrant multiplier with VC Offset that can act as Dual Ring Modulator, Dual VCA, and Four-Channel Mixer. FEATURES Each of the two sections of the module...

Partial Kits

Kickall Partial Kit

PTDIY023

€45.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Kickall module. Includes PCB/Panel Set + Rare parts. Kickall is a 6HP compact synth voice that features everything needed to make a big fat Kick sound: A stable VCO that tracks V/Oct, a couple of VCAs, envelopes for volume and pitch, and an aggressive waveshaper. The module has been designed with a...

Full Kits

STMix DIY Kit

DIY022

€65.00

DIY kit version of our STMix Eurorack module. The kit includes all the necessary parts to make a completed module including PCB, components, aluminium front panel, power cable and a set of our bespoke Knurlies M3 rack screws. STMix is a compact 4 channel stereo mixer with an auxiliary input. This input will allow us to chain a few of them or to insert...

Partial Kits

Instrument Interface Partial Kit

PTDIY032

€54.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Instrument Interface module. Includes PCB/Panel Set + Rare parts. Instrument Interface is an eurorack pre-amp capable to bring any type of audio signal to modular levels thanks to its amplification circuit. The module can drive regular and condenser microphones (+48V Phantom Powered) as well as...

Full Kits

Hex Mix VCA DIY Kit

DIY016

€165.00

DIY kit version of our Hex Mix VCA Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and four of our bespoke Knurlies M3 rack screws. Hexmix VCA is a compact six channel VCA with a unique response curve range from logarithmic to linear and to exponential using a pot. All outputs are routed to...

Partial Kits

Dual Attenuverter Partial Kit

PTDIY007

€35.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Dual Attenuverter module. Includes PCB/Panel Set + Rare parts. The Dual Atenuverter is a CV/Audio utility module designed to attenuate, invert and apply offset to an input signal. The “ATENUVERTER” pot will multiply your signal by 1 when turned clockwise and -1 when turned anti-clockwise. The...

Full Kits

Crush Delay v3 DIY Kit

DIY006

€125.00

DIY kit version of our Crush Delay v3 Eurorack module. The kit includes all the necessary parts to make a completed module including PCB, components, aluminum front panel, power cable, and a set of our bespoke Knurlies M3 rack screws. Crush Delay v3 is a special Echo-Delay unit based on the PT2399 IC, which is able to offer 400ms of clean delay and up...

Partial Kits

Burst Partial Kit

PTDIY020

€57.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Burst module. Includes PCB/Panel Set + Rare parts. Burst is a Pingable Trigger Burst generator with distribution, probability, and time division control. It will create multiplications of your triggers, leading to doubles, triplets, quintuplets, and true polyrhythms for your modular system. FEATURES...

Full Kits

Joystick DIY Kit

DIY002

€95.00

DIY kit version of our Joystick Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and our bespoke Knurlies M3 rack screws. A compact attenuverting (attenuator-inverter) joystick controller and Gate Generator. With it, you can generate and/or process two control voltages using only one hand....

Partial Kits

BF-22 Partial Kit

PTDIY005

€75.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our BF-22 module. Includes PCB/Panel Set + Rare parts. The BF-22 VCF is a dual Hi/Low-pass filter inspired by the Sallen-Key filter from the early MS-20. FEATURES The module features attenuverters (inverter-attenuators) as an addition to the normal CV control for Cutoff and Resonance and offers a little...

Presoldered KIts

Hexmix Presoldered DIY Kit

SK017

€295.00

Preassembled Full DIY Kit of our Hexmix Module. This kit includes a PCB/Panel Set with all the board components presoldered, only the mechanical parts needs to be assembled. CAREFUL: It is still a DIY kit so success is not guaranteed. Follow the documentation carefully and double check every step. This kit is covered by our Happy Ending service. Hexmix...

Partial Kits

VC ADSR Partial Kit

PTDIY013

€51.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our VC ADSR module. Includes PCB/Panel Set + Rare parts. The VC ADSR is our take on the classic ADSR: now smaller, more powerful, and user friendly. FEATURES Voltage-controlled stages with manual control. Gate output on each stage of the envelope. Push-button and Gate/Trigger input Control of the...

Presoldered KIts

Hexpander Presoldered DIY Kit

SK018

€250.00

Preassembled Full DIY Kit of our Hexpander Module. This kit includes a PCB/Panel Set with all the board components presoldered, only the mechanical parts needs to be assembled. CAREFUL: It is still a DIY kit so success is not guaranteed. Follow the documentation carefully and double check every step. This kit is covered by our Happy Ending service....

Partial Kits

A*B+C Partial Kit

PTDIY001

€45.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our A*B+C module. Includes PCB/Panel Set + Rare parts. A*B+C is a dual, four-quadrant multiplier with VC Offset that can act as Dual Ring Modulator, Dual VCA, and Four-Channel Mixer. FEATURES Each of the two sections of the module is capable of performing the analog multiplication of two signals (A and B)...

Partial Kits

Rampage Partial Kit

PTDIY004

€90.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Rampage module. Includes PCB/Panel Set + Rare parts. Rampage is Befaco’s approach to an old invention: the Serge/Buchla ramp generator. We took the idea of a “patch programmable” function generator/processor, put two units in the same module and expanded them with new functions and ways to combine...

Partial Kits

Joystick Partial Kit

PTDIY002

€57.00

CAREFUL! THIS IS NOT A FULL KIT Partial kit of our Joystick module. Includes PCB/Panel Set + Rare parts. A compact attenuverting (attenuator-inverter) joystick controller and Gate Generator. With it, you can generate and/or process two control voltages using only one hand. Provided controls for CV ranges and offset adjust the boundaries of your control,...

Partial Kits

Sampling Modulator Partial Kit

PTDIY010

€64.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Sampling Modulator module includes PCB/Panel Set + Rare parts. The Sampling Modulator is a multi-function module that lies somewhere between a VCO, a Sample & Hold, and an 8 step trigger sequencer. FEATURES Sequencer Clocked Sample & Hold Analog Down-sampling Effect Sampling Modulator/Shaper...

Partial Kits

Chopping Kinky Partial Kit

PTDIY015

€53.00

CAREFUL! THIS IS NOT A FULL KIT Partial kit of our Chopping Kinky module. Includes PCB/Panel Set + Rare parts. For the complete BOM and more information please refer to our website. Chopping kinky is a voltage controllable, dual-channel wavefolder. As a unique feature, it has a chop out that will choose between both channels with a zero cross detector or...

Partial Kits

Hexmix VCA Partial Kit

PTDIY016

€95.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Hexmix VCA module. Includes PCB/Panel Set + Rare parts. For the complete BOM and more information please refer to our website Hexmix VCA is a compact six channel VCA with a unique response curve range from logarithmic to linear and to exponential using a pot. All outputs are routed to output six to...

Presoldered KIts

Morphader DIY Kit

DIY036

€140.00

DIY version of our Morphader module. This is a pre-soldered kit. All the SMT components are already soldered on the board. Assembly Manual and documentation. Morphader is a performative tool designed to make multichannel CV/Audio crossfade easy and comfortable. Fading from one quad CV/audio scene to another. The core of the module has four CV-controlled...

Partial Kits

Crush Delay Partial Kit

PTDIY006

€67.00

CAREFUL! THIS IS NOT A FULL KIT The partial kit of our Crush Delay module. Includes PCB/Panel Set + Rare parts. For the complete BOM and more information please refer to our website. Crush Delay v3 is a special Echo-Delay unit based on the PT2399 IC, which is able to offer 400ms of clean delay and up to 2 seconds of dirty repetitions, having a special...

Partial Kits

Even VCO Partial Kit

PTDIY014

€59.00

CAREFUL! THIS IS NOT A FULL KIT Partial kit of our Even VCO module. Includes PCB/Panel Set + Rare parts. For the complete BOM and more information please refer to the website. The Even VCO is a voltage controlled oscillator which offers stability even in the case of power supply fluctuations. 10 position octave selector 1 cent precision tracking on the...

Full Kits

Muxlicer DIY Kit

DIY019

€125.00

DIY kit version of our Muxlicer Eurorack module. The kit includes all the necessary parts to make a completed module including power cable and four of our bespoke Knurlies M3 rack screws. Muxlicer is a sequential signal processor designed to add a huge range of special functions to your modular setup in the minimum space. Is divided into three main...